banner

Three precautions for wireless transceiver module development

236 Published by xia, Crystal Dec 21,2018

Want create site? Find Free WordPress Themes and plugins.

Wireless transceiver modules are widely used in vehicle monitoring, remote control, telemetry, small wireless networks, wireless meter reading, access control systems, cell paging, industrial data acquisition systems, wireless tags, identification, contactless RF smart cards, small wireless data terminals, security Fire protection system, wireless remote control system, biological signal acquisition, hydrometeorological monitoring, robot control, wireless 232 data communication, wireless 485/422 data communication, digital audio, digital image transmission and other fields.Here are three tips for developing wireless?transceiver module.

wireless transceiver module application range.

The wireless transceiver module must use signal modulation to work properly. Common fixed code encoding devices such as PT2262/2272 can be directly connected, which is very simple. Because it is a special encoding chip, the effect is very good.

Another important use of the wireless?transceiver module is to use the microcontroller to achieve data communication. There are certain skills:

1. A reasonable communication rate

The maximum transmission data rate of the data module is 9.6KBs, which is generally controlled at about 2.5k. Excessive data rate will reduce the receiving sensitivity and increase the bit error rate or even work at all.

2. Reasonable information code format

wireless transceiver module YET205B

When the MCU and the module work, they usually define the transmission protocol by themselves. Regardless of the modulation method used, the format of the information code to be transmitted is very important, which will directly affect the reliable transmission and reception of data.

Code group format recommendation scheme: preamble + synchronization code + data frame, the preamble length should be greater than 10ms to avoid background noise, because the first bit of data received by the wireless transceiver module is easily interfered (ie, zero-level interference). The data received is incorrect. Therefore, using the CPU code can add some garbled code before the data identification bit to suppress zero-level interference. The sync code is mainly used to distinguish it from the preamble and data. There are certain characteristics, so that the software can identify the synchronization code through a certain algorithm and prepare for receiving data. Data frames should not use non-return to zero code, but not longer 0 and longer 1. Manchester code or POCSAG code is used.

3. The interference of the single chip to the receiving module

When the MCU simulates 2262, it is generally normal. However, when the MCU simulates 2272 decoding, it usually finds that the remote control distance is shortened a lot. This is because the multiplier of the clock frequency of the MCU will interfere with the receiving module. The electromagnetic interference of the 51 series MCU is relatively large, 2051 Slightly smaller, the PIC series is smaller, we need to use some anti-interference measures to reduce interference. For example, the single-chip microcomputer and the remote control receiving circuit are respectively powered by two 5 volt power sources, and the receiving board is separately powered by a 78L05. The clock area of the single chip microcomputer is far away from the receiving module, the working frequency of the single chip microcomputer is lowered, and the shielding is added in the middle.

It is better to make an isolation circuit when receiving the module and the 51 series MCU interface, which can better suppress the electromagnetic interference of the MCU to the receiving module. When the wireless transceiver module works, it generally outputs a high-level pulse, which is not a DC level, so it cannot be tested with a multimeter. When debugging, an LED can be connected in series with a 3K resistor to monitor the output state of the module. When the wireless data module and the dedicated codec chip such as PT2262/PT2272 are used, the connection is very simple. As long as it is directly connected, the transmission distance is ideal, generally up to 600 meters. If used with a single chip microcomputer or a microcomputer, it will be subjected to a single chip microcomputer or a microcomputer. The clock interference causes the transmission distance to drop significantly, and the general practical distance is within 200 meters.

 

Shenzhen Yaoertai Technology Co., Ltd. specializes in (RF) wireless transceiver module, wireless remote control, wireless receiver, wireless controller, infrared detector, door magnet, smoke detector, gas alarm, burglar alarm, etc. A high-tech enterprise that develops, manufactures and sells related products. Wireless controller accessory products are widely used in remote control electric windows and doors, retractable doors, garage doors; remote control lights, switches, communications and security. Professional supporting garage door factory, GPS factory, security factory, electric control lock factory, automobile factory, electric door and window, gateway, industrial control, etc. Welcome everyone to come to consult!

Did you find apk for android? You can find new Free Android Games and apps.

Celebrate the 14th anniversary of Yaoertai !

On May 11, 2019, our company Yaoertai was founded 14th anniversary! In the past 14 years, we hav...

Do you like ? 43

Read more

2019, let’s go hiking together!

Saturday, the first week of work in 2019, On a sunny afternoon, Yaoertai, all business colleagues...

Do you like ? 330

Read more

The 28th Beijing Construction Expo will be held soon, and invite you to participate in the grand event!

The 28th China (Beijing) International Building Decoration and Materials Expo will be held on Mar...

Do you like ? 533

Read more

R+T Asia Shanghai Door and Window Sunshade Exhibition, the opening of the 2019 is coming soon

The 15th R + T Asia Shanghai Door and Window Sunshade Exhibition will be held from February 27th ...

Do you like ? 509

Read more

Difference between 433 remote control and 315 remote control and its code method

The frequency used by the radio remote control is 433Mhz or 315Mhz, also referred to as 433 remot...

Do you like ? 736

Read more

Infrared alarm principle, function and installation method

The infrared alarm can detect the infrared rays emitted by the human body, and is composed of an ...

Do you like ? 484

Read more

Congratulation YET Global Sources Electronics Exhibition bring to a successful close

Congratulation YET Global Sources Electronics Exhibition bring to a successful close Gate remote ...

Do you like ? 552

Read more

Best wifi receiver and wifi smart plug for home security

? The WiFi Smart Product is a product with a good idea. It utilizes the WiFi network in the exist...

Do you like ? 599

Read more
YET2018All Rights ReseverdTechnical Support:Baiila