Explain The Wiring of The Electric Door Wireless Controller and Its Installation

1,245 Published by xia, Crystal Apr 08,2019

Want create site? Find Free WordPress Themes and plugins.

The electric door is a management device for controlling personnel or vehicles to enter and exit. Generally, it is installed at the gate of a factory, a community or a hotel. The inrush current of the electric door itself and other interferences generated are relatively large. Therefore, when installing the electric door wireless controller, it is recommended to contact the manufacturer’s technical personnel to perform wiring and operation under the guidance of the manufacturer to ensure the stability of the system. The following is a detailed explanation of the wiring and installation of the electric door wireless controller.

sliding door wireless controller motor controller.

Wiring of the electric door wireless controller:

There are two main ways of wiring the electric door wireless controller. One is the external wiring, the other is the built-in wiring. The external type is to install the controller of the electric door in the guard room, between the motor of the telescopic door and the controller. It is connected by a seven-core electric door special cold-proof flat wire. The COM terminal on the motor represents the common line of the motor and the motor common port of the controller. The method of connecting the stroke switch line is to connect two magnetic-sensitive switches on the motor base. Each of the upper lines is connected together, connected to the controller’s travel common port, and the remaining two lines are respectively connected to the open limit and the closed limit. The two wires on the warning light on the chassis are connected to the common end of the motor and the door opening signal, and then the 220V power supply is connected to the 220V port of the controller, even if the basic function wiring is completed.

Electric door wireless controller installation:

It should be properly installed by a professional in accordance with the instructions. The power cable and the motor power cable should be copper-sheathed cable with a wire diameter of not less than 1.5mm2, and other control wires should be copper-core cables with a wire cross-section of not less than 0.5mm2. The power line should be connected to the L terminal of the controller, and the neutral line should be connected to the N terminal of the controller. In-flight insurance should use Ф5×20mm/6A quick-blow fuses. It is strictly forbidden to use the internal fuse for direct short-circuit use. The door motor of the electric door should be connected to the P1 terminal block inside the machine. The alarm should be connected to the P4 terminal block inside the machine. Other basic control lines should be connected to the P2 terminal block inside the machine. When installing the wiring, refer to the wiring diagram attached to the product for proper connection. In particular, be careful not to connect the low voltage control line to the high voltage terminal or the high voltage control line to the low voltage terminal. Wiring installation of the controller In addition to the items specified in this product, other matters shall comply with the relevant provisions of the electrical safety operating procedures. The installation position of the controller is selected according to the specific conditions of the user and suspended on the wall of the five magnetic field interference. The installation height should not be less than 1.2m from the ground. The outgoing cable should be securely fastened along the wall. All installation work should be thoroughly checked before power-on, and the test machine can be sent after confirmation. The probe is mounted at an appropriate height outside and the angle can be adjusted.

The working principle of the electric door wireless controller is that the electric door operation end has three buttons, one followed by one line, and one common line. The line and the common line of the opening button are connected to the NO and COM of the relay control end of the access controller. Just fine. This will open the electric door by swiping control. The current and voltage of the electric door button will cause large interference, and even if it may cause a crash or restart, please install an intermediate relay or other isolation control circuit under the guidance of the technician to make the product stable and long-term operation. . If you want to know more about how the access controller controls the electric door, please consult the remote customer service!

The price of electric door controllers on the market is currently diverse. According to the sales strategy of the electric door wireless controller manufacturer and the production cost, there will be a certain degree of deviation in the price on the market. In terms of pricing of electric door controllers, Yaoertai Technology fully considers customers. The price of the electric door controller is fair and reasonable, which can help customers save costs and meet actual needs. At the same time, Yaoertai Technology provides customers with complete after-sales protection, so that customers have no worries.

Did you find apk for android? You can find new Free Android Games and apps.

2019 China Shenzhen Public Security Expo!

Focus on security technology innovation and lead the development of AI industry. The 17th China I...

Do you like ? 3,689

Read more

Celebrate the 14th anniversary of Yaoertai !

On May 11, 2019, our company Yaoertai was founded 14th anniversary! In the past 14 years, we hav...

Do you like ? 3,511

Read more

2019, let’s go hiking together!

Saturday, the first week of work in 2019, On a sunny afternoon, Yaoertai, all business colleagues...

Do you like ? 4,612

Read more

The 28th Beijing Construction Expo will be held soon, and invite you to participate in the grand event!

The 28th China (Beijing) International Building Decoration and Materials Expo will be held on Mar...

Do you like ? 4,552

Read more

R+T Asia Shanghai Door and Window Sunshade Exhibition, the opening of the 2019 is coming soon

The 15th R + T Asia Shanghai Door and Window Sunshade Exhibition will be held from February 27th ...

Do you like ? 3,832

Read more

Difference between 433 remote control and 315 remote control and its code method

The frequency used by the radio remote control is 433Mhz or 315Mhz, also referred to as 433 remot...

Do you like ? 19,772

Read more

Infrared alarm principle, function and installation method

The infrared alarm can detect the infrared rays emitted by the human body, and is composed of an ...

Do you like ? 4,196

Read more

Congratulation YET Global Sources Electronics Exhibition bring to a successful close

Congratulation YET Global Sources Electronics Exhibition bring to a successful close Gate remote ...

Do you like ? 4,360

Read more
YET2018All Rights ReseverdTechnical Support:Baiila